Differences

This shows you the differences between two versions of the page.

--- mobil:assemblies:structures:tour [2026/06/21 14:07] – yannick
+++ mobil:assemblies:structures:tour [2026/06/23 09:06] (current) – external edit 127.0.0.1
@@ Line 1: / Line 1: @@
-====== tower ======
+====== Tour ======
+{{tag>assembly structure visibility}}
+//A stacked tube-and-connector tower — height and visibility from the same 1,33 m module. Banners, light or a lookout, depending on what you mount on it.//
+  * **Type:** Structure
+  * **Status:** In use
+  * **Primary function:** visibility / height / signal
+===== 1. At a glance =====
+^ Specification      ^ Value          ^
+| Footprint          | 3,99 x 3,99 m  |
+| Height             | 3,99 m         |
+| Volume             | 63,44 m3       |
+| Total weight       | 114,9 kg       |
+| Assembly time      | . //(to define)// |
+| People needed      | . //(to define)// |
+| Tools              | Hammer (optional, for pins) |
+===== 2. 3D model & steps =====
+{{url>https://mobil.brussels/wiki/three-viewer/viewer/index.html?p=tower 100%,720px noborder noscroll}}
+//If the model doesn't load, [[https://mobil.brussels/wiki/three-viewer/viewer/index.html?p=tower|open it in a new tab]].//
+===== 3. Parts (bill of materials) =====
+Everything you need to build one tour. All tubes diameter 50 x 2 mm wall. Click a part for specs and handling.
+^ Part ^ Qty ^ Spec ^
+| [[mobil:parts:core_kit:short_tube|Straight tube]]      | 40 | 1329,4 mm |
+| [[mobil:parts:core_kit:long_tube|Diagonal tube (45)]]  | 30 | 1880,1 mm |
+| [[mobil:parts:core_kit:t_connector|T-connector]]       | 48 | 2 per connector node |
+| [[mobil:parts:core_kit:x_connector|X-connector]]       | 24 | 1 per connector node |
+| [[mobil:parts:core_kit:locking_pin|Locking pin]]       | .  | 1 per tube-connector joint |
+| [[mobil:parts:hub_elements:panel_square|Panel]]        | 12 | 1329,4 x 1329,4 mm //(panel type to confirm)// |
+  * **Connector nodes:** 24 (each = 2x T + 1x X)
+  * **Tubes total:** 70 - **tube length:** 109,58 m
+  * **Tube weight:** 89,2 kg - **connector weight:** 25,7 kg - **total:** 114,9 kg
+//Source: MoBil builder. Locking-pin count and panel type to confirm.//
+===== 4. Assembly =====
+The tour is stacked from connector nodes. Each node = the [[mobil:assemblies:structures:connector|connector]] assembly (2x T + 1x X), joined by tubes. Built flat, then tilted upright.
+  - **Lay out the base level.** Three squares side by side on the ground; join the nodes with straight tubes.
+  - **Add the verticals.** One straight tube into each ground node, pointing up; connect.
+  - **Close the top surface.** Cap with straight tubes.
+  - **Add panels.** Mount square panels where wanted.
+  - **Tilt 90 and add the base.** Stand the structure upright on its hinge, then add the base for stability.
+//Each step maps to a stage in the viewer above.//
+===== 5. Safety & correct use =====
+==== Build safety ====
+  * Pinch points at every connector - keep fingers clear when seating joints.
+  * Don't hammer pins with the frame unsupported; seat the joint by hand first.
+  * Tilting a tall frame upright needs enough hands - never lift it short-handed.
+==== Use & load limits ====
+  * **Max vertical load (stage/roof):** . kg //(to define / test)//
+  * **Do not climb** the frame unless rated and ballasted.
+  * **Wind:** above . km/h, remove banners and ballast or take down. //(define - tall, wind-critical)//
+  * Never leave a tall configuration up unattended in changing weather.
+==== Ballast / anchoring ====
+  * Footprint anchoring with [[mobil:parts:accessories:water_weight|water weights]] at the base corners - mandatory for any raised or sail-bearing configuration.
+  * [[mobil:parts:accessories:ropes|Ropes]] to fixed points where available.
+  * Minimum ballast: . kg per corner //(define per configuration)//.
+===== 6. Takedown & storage =====
+  - Remove add-ons and ballast first.
+  - Tilt the frame back down flat before breaking joints.
+  - Pull top pins, lift off top surface.
+  - Pull verticals.
+  - Break the base levels. Nodes can stay assembled for next time, or break to flat-pack.
+  * **Packs into:** [[mobil:parts:logistics:normal_bike_trailer|normal bike trailer]] (tubes + euroboxes for connectors).
+  * Store dry. Check pins aren't bent before repacking.
+===== 7. Compatible add-ons =====
+What this tour accepts:
+  * [[mobil:assemblies:modules:banners|Banners]]
+  * [[mobil:assemblies:modules:light_inflatable|Light inflatable]]
+===== 8. Media & credits =====
+  * Photos - Drawings - Exploded diagram
+  * Linked: [[mobil:assemblies:structures:connector|Connector]] (the core joint)
+//Designed by . - Year . - Iteration . - Last updated: .//
-{{url>https://mobil.brussels/wiki/three-viewer/tower/index.html}}